Omniadisce

Pad footing calculator: bearing capacity and settlement

A square or rectangular concrete pad under a column, on one soil with a water table. The calculator checks the bearing resistance (EN 1997-1 Annex D, design approach 1) and works out the settlement.

Learn how this works
Ground
Footing
Loads
All 2 checks pass. The worst is at 90% of its limit.

Results

Footing thickness0.60 m
Footing self-weight128.6 kN
Net bearing pressure q_net264.7 kPa
Bearing at base, drained, DA1-C12,289 of 5,916 kN
Bearing at base, drained, DA1-C21,809 of 2,825 kN
Settlement22.5 mm

Checks

  • Bearing resistance (drained, DA1-C2) 64%

    EN 1997-1 6.5.2, Annex D ยท 1808.6 against 2824.6 kN

    R / A = c' N_c s_c + q' N_q s_q + ยฝ ฮณ' B N_ฮณ s_ฮณ

    Governing case: Bearing at base, drained, DA1-C2. Medium dense sand: design ฯ†' = 26.6ยฐ (so N_q = 12.6, N_ฮณ = 11.6), c' = 0.0 kPa, overburden q' = 18.0 kPa, ฮณ' = 16.7 kN/mยณ, area 2.40 ร— 2.40 m: R_d = 2825 kN. Design load 1809 kN.

    Friction on the grains carries the load; the soil above the base (q') and the footing width both help, and water lowers both by reducing the effective stress.

  • Settlement 90%

    limit 25 mm (EN 1997-1 Annex H) ยท 22.5 against 25 mm

    s = ฮฃ ฮ”ฯƒ ฮ”z / E (sand, gravel) + ฮฃ ฮ”z C_c / (1 + e_0) ยท log((ฯƒ'_0 + ฮ”ฯƒ) / ฯƒ'_p) (clay)

    Net pressure 265 kPa spreads into the ground (Boussinesq). Immediate settlement 22.5 mm, clay consolidation 0.0 mm: 22.5 mm against 25 mm.

    Clay squeezes water out slowly and keeps settling for years; sand settles at once and little.

Key formulas

Drained bearing resistance (EN 1997-1 D.4)
R / A' = c' N_c b_c s_c i_c + q' N_q b_q s_q i_q + 0.5 ฮณ' B' N_ฮณ b_ฮณ s_ฮณ i_ฮณ
Bearing factors
N_q = e^{ฯ€ tan ฯ†'} tanยฒ(45ยฐ + ฯ†'/2), N_ฮณ = 2 (N_q โˆ’ 1) tan ฯ†'
Consolidation settlement
s = ฮฃ m_v ฮ”ฯƒ' h
Design approach 1
C1: 1.35 G + 1.5 Q; C2: 1.0 G + 1.3 Q with tan ฯ†' / 1.25
Assumptions
  • Vertical, centric load; no depth or inclination factors (conservative).
  • Design Approach 1: C1 = 1.35 G + 1.5 Q with characteristic soil; C2 = 1.0 G + 1.3 Q with tan ฯ†'/1.25, c'/1.25, cu/1.4.
  • Weaker layers within 2B are checked with the load spread at 2:1.
  • Settlement under the centre from the characteristic load G + Q. Granular soils: ฮ”ฯƒ/E; clays: Cc / Cr with the preconsolidation from OCR.
  • Consolidation in time: Terzaghi 1D, implicit finite differences; drainage at sand, gravel or silt boundaries.
Learn how this worksBuild it yourself in the Soil lab, with guided lessons and challenges.
× Enlarged view