Omniadisce
Weten

Weten

Joined October 2026 0 reputation

1problem solved
100%solved of 1 attempted
312posts
0lists

Progress by subject

  • Physics 1 of 1

    Physics: solution viewedClassical Mechanics: 1 of 1Electromagnetism: solution viewed

  • Biology & Life Sciences โ€“

    Biology & Life Sciences: solution viewed

  • Chemistry โ€“

    Chemistry: solution viewed

  • Logic & Foundations โ€“

    Logic & Foundations: solution viewed

  • Mathematics & Formal Sciences โ€“

    Mathematics & Formal Sciences: solution viewedGeometry: solution viewed

Solutions viewed before answering don't count as attempts.

Recent answers

Latest posts

Lesson
Civil Engineering Beginner Lesson

How should a beam fail?

If a beam must fail, it should fail slowly and visibly. Engineers design for that. A beam can fail in bending (bars yield, cracks open wide, it sags a lot: plenty of warning), in shear (a diagonalโ€ฆ

4 views by Weten 13 days ago
Lesson
Civil Engineering Beginner Lesson

Supports push back

Shelves, floors and bridges all start with the same question: how hard must each support push to hold the load up? A beam stays put because its supports push back. Those pushes are the reactionsโ€ฆ

6 views by Weten 13 days ago
Lesson
Civil Engineering Beginner Lesson

Bending moment

A beam breaks where it bends hardest. This lesson finds that place. Inside the beam, the material resists turning: the bending moment. Cut the beam anywhere, and the moment there equals the momentโ€ฆ

5 views by Weten 13 days ago
Lesson
Civil Engineering Beginner Lesson

Spread loads

Floors, snow and crowds spread their weight. This lesson shows why long spans are hard. Floors, snow and people spread their weight: a uniformly distributed load $w$ in kN/m. For moments, it actsโ€ฆ

7 views by Weten 13 days ago
Lesson
Civil Engineering Beginner Lesson

Why engineers add safety factors

No one knows exactly what a floor will carry. Engineers plan for bad luck. Loads are uncertain and materials vary. Eurocodes deal with this with partial factors: the design load is bigger than theโ€ฆ

9 views by Weten 13 days ago
Lesson
Civil Engineering Beginner Lesson

Choosing a section

Too small fails; too big wastes steel, money and carbon. The engineer finds the one in between. A steel beam resists bending until its whole cross-section yields: โ€ฆ

7 views by Weten 13 days ago
Lesson
Civil Engineering Beginner Lesson

Strong is not stiff

A floor can be perfectly safe and still feel like a trampoline. A beam can be strong enough and still sag too much. Deflection depends on stiffness $E \cdot I$, not on strength.

7 views by Weten 13 days ago
Lesson
Civil Engineering Beginner Lesson

What the model leaves out

Software only checks what it was built to check. Engineers check the rest. Every model simplifies. This lab assumes the top flange of a steel beam is held sideways by the floor it carries.

8 views by Weten 13 days ago
Lesson
Civil Engineering Beginner Lesson

Triangles do not fold

Look at any bridge, crane or roof made of bars: it is all triangles. This lesson shows why. A square of four bars joined by pins folds flat at the slightest push: it is a mechanism. A triangleโ€ฆ

7 views by Weten 13 days ago
Lesson
Civil Engineering Beginner Lesson

Pulling and pushing

Every member of a truss is either pulled or pushed. Knowing which is half of designing it. Truss members carry only axial force: tension (pulled) or compression (pushed). A truss bridge acts like aโ€ฆ

5 views by Weten 13 days ago
Lesson
Civil Engineering Beginner Lesson

Buckling

Pushed members don't break. They buckle, and much sooner than you'd think. A slender compression member fails long before the steel yields: it bows sideways and buckles. Euler worked out theโ€ฆ

5 views by Weten 13 days ago
Lesson
Civil Engineering Beginner Lesson

Effective stress

Every building stands on soil, and soil is only as strong as the water in it lets it be. Soil is grains with water in between. The grains carry part of the weight above; the water carries the restโ€ฆ

5 views by Weten 13 days ago
Real Analysis Intermediate Multiple choice

Is Thomson's lamp on or off?

A lamp has a single button that switches it between on and off. At $t = 0$ the lamp is on. After $1$ minute you press the button. After another $\tfrac12$ minute you press it again, then afterโ€ฆ

NewBe the first to try 18 views by Weten 19 days ago
Simulation
Fluid Dynamics Beginner Simulation

How much cargo takes a barge down to its load line?

A box-shaped barge $5\ \text{m}$ long and $3\ \text{m}$ wide floats in a harbour of sea water at $15\ ยฐ\text{C}$, which has a density of $1026\ \text{kg/m}^3$. The empty barge has a mass of โ€ฆ

NewBe the first to try 17 views by Weten 20 days ago

No public lists.

× Enlarged view